Mike can you build me a map for purchase? I called you from MD

[jshepherd]

Mike I talked to you on Thursday and sent an email I think to your shop not sure if you received it or if the email address was copied correctly.


I’m in the process of building a 95 ci 2006 Night Train EFI. I’m looking for a map that will be safe for break-in until I can get it down to DOC at MMI. I’m sending a list of the parts used. Please reply to jshepherd61@comcast.net.


PARTS:



Dewey’s ProStreet Heads Milled .060 for 10.5:1 Compression $950.00



ZIPPER’S bored Jugs 3.875 Bore $197.95



Dakota Kid Bored EFI 48mm narrowed .035 End-To-End $365.00



Machine Work C&C Cycles $60.00



Fuel Injectors Blue Printed $67.00



JIMS Hydrosolid Lifters #DS-194345 (1802) $320.00



Andrews Chromoly EZ adj Pushrods #DS-199013 $142.95



AIM-Tamachi Variable Pressure Clutch # VP-002-83S (VP83S) $210.00



SE Clutch Spring #37951-98 $34.99



Wiseco 9:1 comp forged FT pistons #K1918 $247.99



Dougherty’s Mystfree # $192.85



Screamin Eagle Race Tuner # $329.95



Rinehart Staggered Duals # $567.99



SE 90 degree Air Filter # $278.95



CP Compression SS Releases # $49.94



Cometic Full Gasket Set .030 Head # $139.50



Baisley Oil Spring # $10.99



Andrews Cam Gears #DS-199538 $380.95



Andrews Cam install Kit #DS-199235 $78.95



Andrews 67G .570 Lift Gear Dr Cams # $238.95



My compression will be between 10.5 – 10.7:1 Dewey and DOC from MMI in FL both say the heads flow considerably more than the SE HTCC heads and it’s a .570 lift cam Rinehart staggered duals. If you can please let me know the cost and I’ll call and pay for it over the phone I have the 2006 version of the SERT. Frederick Harley Davidson in Frederick, MD did the initial tune but I’m building the bike and I live an hour away so have to break it in before I get it to DOC in MMI. Please feel free to call my cell any time (301) 758-3540.



Thank you



Jerry Shepherd

4003 Woodhaven Ln

Bowie, MD 20715

(301) 758-3540




-----
Jerry W Shepherd
Bowie, MD
jshepherd61@comcast.net

[Mike]

I looked for your e-mail but did not recieve. May have forgot the "." between first and last name. Our maps are $47.50 and can be sent via e-mail. I'll confirm which we would like to use, maybe modifiy it slightly for breakin and e-mail you directly tuesday.
Thanks, Mike

[jshepherd]

Thanks Mike much appreciated you can reach me at jshepherd61@comcast.net (301) 758-3540

[Mike]

Sent an E-mail and hope we can finallize. You may hae told me but are the blueprinted injectors 25 or 8 degree?
Thanks, Mike

[jshepherd]

they are 8 degree, that was one of the questions I had also I just received the tech notice on the 25 degree injectors. I did not have a problem with my 8 degree injectors but is there any advantage to the 25 degree injectors for this build? If they have an advantage I will contact Frederick HD in MD where I purchased the bike and see if they will send me the 25 degree injectors and I'll send back the 8 degree.

[Mike]

No advantage with the 25's when used with with Race Tuner. The difference can be accounted for through the tuning process. Thanks, Mike

[jshepherd]

Mike were you able to come up with a MAP for me? Let me know and I'll call and pay for it over the phone. I should be complete with my build by the middle of next week, just waiting on the mystfree oil seperators before I put the tank and seat back on it!</p>

</p>

Jerry Shepherd</p>

(301) 758-3540</p>

[Mike]

You should get a call from our I.S. gal (Jolain) for purchase info. Note that the map is not a an exact match but will be modified and can be used as a good base for final mapping. I'll explain some details in a private E-mail to you.
Thanks, Mike

[jshepherd]

Thanks Mike I didn't see this before I replied to your personal message this makes since now. I'll wait for Jolain's call.

[Mike]

Got you sqaured away! Let us know how it works out! Thanks again, Mike

[jshepherd]

Thanks Mike I'll let you know how it is and if I end up making adjustments I'll send it back for you to shelf.